Hamilton Beach Commercial Blender Error 60 and 62: Corrupt EEPROM Data
Errors 60 and 62 on a Hamilton Beach Commercial HBH750, HBH755 or HBH850 blender mean the EEPROM, the chip that stores settings, is defective or holds corrupt data. Pull the plug, reseat it firmly, and check that the jar is seated. If the error returns, stop restarting the blender and call us.
Medium: the blender may not run its programs, and the cause is in the control boards rather than a safety circuit.
- Code
- Error # 60, # 62
- Equipment
- Blenders
- Applies to
- HBH750 / HBH755 / HBH850 display
What does Hamilton Beach Commercial error # 60 mean?
Every time the blender powers up, its control reads stored settings from a small memory chip. The control checks that what it reads makes sense. When the chip cannot be read or its contents fail that check, the control shows Error 60 or Error 62 and may refuse to run its programs, or it may behave oddly. This is a different situation from numbers 29, 30, 42, 100 and 103, which describe a lost conversation with the chip; here the chip itself is suspect, either defective or carrying damaged data. A power event such as a surge or a plug pulled in the middle of a save can damage stored data, and a chip that has been damaged once may corrupt again after a reset. The maker's data sheet puts the repair on the display board and does not suspect the motor. The display text reads Error # 60, # 62, and the board for the model should be confirmed before anything is ordered.
Affected models and control systems
Hamilton Beach Commercial HBH750, HBH755 and HBH850 blenders. Errors 29, 30, 42, 100 and 103 on the same models describe a communication problem instead.
Code numbers and their meaning can change between control generations. We match the full model and control before acting on a code.
What you may notice
- 60 or 62 on the display
- Programs missing or behaving unpredictably
- Blender will not run after power-up
Possible causes
Listed in Hamilton Beach Commercial's documentation
- Display board and its memory chip
- Connectors and wiring between the boards
- Power events that may have damaged the stored data
- Main control board, if the display board tests good
Other likely causes — what usually sits behind error # 60 on this control. A technician confirms which one it is before any part is replaced.
- A surge or a plug pulled while the blender was saving a setting
- A display board that has been replaced once and carries the same weak memory part
Safe checks before calling for service
- Pull the plug and reseat it firmly in the outlet.
- Check that the jar is seated on the base.
- Note whether 60 or 62 is shown.
- If the error returns, do not keep restarting the blender.
- Call us and tell us which number appeared and whether the outlet shared a circuit with large equipment.
How a technician diagnoses error # 60
- Record whether the display reads 60 or 62 and when it appears.
- Check outlet voltage and the plug for damage or looseness.
- Inspect board connectors for corrosion and poor contact.
- Swap in a known good display board and see whether the error clears.
- If the display board tests good, evaluate the main control board.
- Confirm the replacement board is the correct part number for the model.
- The boards sit under the base with line voltage present, so they are not a bench job for an operator.
- Corrupt data can return after a reset if the chip is damaged, so a reset proves nothing.
- Choosing the right board for HBH750, HBH755 or HBH850 needs the model and serial information in hand.
Technical reference
- Document
- Hamilton Beach Technical Data Sheet GB34 HBH750/HBH755 (Doc 520008100 Rev B, 2024) and HBH850 (Doc 520004200)
- Edition
- Document # 520008100, Rev: B, revision date 05-Sep-2024 (Revised added Error 51 info); form ENG-FRM-RIC-4.32 Rev. E
- Models / control
- HBH750 / HBH755 / HBH850 display
- Section
- Trouble Shooting Guide, pp. 1-2 (error # 29/30/42/100/103 at end of p. 1 into p. 2; error # 60/62 and error # 51 on p. 2; Speed Sensor Failure/Error on p. 1)
- Checked
- October 2026
We use the maker's document to read the code and do not reproduce it. Always confirm the complete model and control before applying these steps.
Related Hamilton Beach Commercial blender error codes
Is 60 the same as 62?
The data sheet gives them the same meaning, a defective or corrupt memory chip.
Can I clear it by unplugging?
A reset may bring the blender back briefly, but damaged data can return.
Is the motor bad?
The data sheet does not suspect the motor for these two numbers.
Need help with Hamilton Beach Commercial error # 60?
A technician confirms the cause on site and gives you the price in writing before any work starts.