Taylor Slush Machine Error Code Beater Overload: Motor Overload
On the Taylor C300 slush freezer, Beater Overload means the beater motor has gone out on overload. The machine turns itself off, and the message clears once the condition is corrected. Leave it off and let the motor cool, look at the product from the top without reaching in, and tell us if it looks frozen solid.
High: the machine turns itself off and will not run until the overload cause is corrected.
- Code
- Beater Overload
- Maker
- Taylor
- Equipment
- Slush & frozen drinks
- Applies to
- Model C300 frozen carbonated beverage / slush freezer
What does Taylor Beater Overload mean?
The beater in a Taylor C300 slush freezer turns the frozen carbonated drink inside the barrel. It works hard when the product is too thick or when the drive is binding. The beater motor has an overload protection, and if the motor draws too much current, the control takes the motor out and the display shows Beater Overload. The machine turns itself off, and the message clears once the condition is corrected. That makes the first question what made the motor labor in the first place. The manual's reasons include a frozen drink that has set too thick in the barrel, a beater that binds or has worn in the drive, a beater motor that trips its overload protector early, and low supply voltage at the outlet straining the motor. Mix that is wrong, or supplies of syrup, water or CO2 that ran out, can leave the barrel too thick, so check those as well before calling.
Affected models and control systems
Taylor Model C300 frozen carbonated beverage / slush freezer.
Code numbers and their meaning can change between control generations. We match the full model and control before acting on a code.
What you may notice
- The machine shuts off with Beater Overload on the display
- The product in the barrel looks very thick or frozen hard
- The beater does not turn when the machine is restarted
Possible causes
Listed in Taylor's documentation
- Frozen drink that has set too thick in the barrel
- A beater that binds or has worn in the drive
- A beater motor that trips its overload protector early
- Low supply voltage at the outlet straining the motor
Other likely causes — what usually sits behind Beater Overload on this control. A technician confirms which one it is before any part is replaced.
- A mix ratio that is off so the barrel freezes harder than it should
- A beater drive coupling that has worn and now sticks under load
Safe checks before calling for service
- Leave the machine off and let the motor cool.
- Look at the product in the barrel from the top, without reaching in. If it looks frozen solid, tell us.
- Check that the product mix is correct and the syrup, water and CO2 supplies are all on.
- Do not put hands or tools near the beater, and tell us how thick the product looked when you call.
How a technician diagnoses Beater Overload
- Read the message and ask how long the machine ran before the shutdown.
- Check the product consistency and the mix settings.
- With power off and locked out, turn the beater by hand to check for binding.
- Measure the voltage at the outlet and the motor current when it starts.
- Inspect the drive coupling and seals for wear.
- Replace the motor or the drive part only after the test.
- A beater can pinch or cut, and a barrel of thick frozen product is unsafe to reach into.
- The motor circuit carries live voltage, and the overload reading needs a meter.
- Telling a worn drive from a weak motor means disassembling parts under sanitary rules.
Technical reference
- Document
- Model C300 Operator's Manual (updated 9/2/2020), User Interface p.5-2 to 5-4
- Edition
- 055072-M; original publication 9/26/08, updated 9/2/2020
- Models / control
- Model C300 frozen carbonated beverage / slush freezer
- Section
- Section 5 User Interface - Table 5-1 Fault Messages p. 5-2 (PDF p. 20); fault explanations pp. 5-3 to 5-4 (PDF pp. 21-22)
- Checked
- October 2026
We use the maker's document to read the code and do not reproduce it. Always confirm the complete model and control before applying these steps.
Related Taylor slush & frozen drink error codes
Will Beater Overload clear by itself?
The message clears once the condition is corrected, so a cooled motor and thinner product may allow a restart.
Can I stir the barrel by hand?
No. Keep hands and tools away from the beater.
Why does thick product matter?
A beater working in product that has set too hard draws more current, which is what trips the overload.
Need help with Taylor Beater Overload?
A technician confirms the cause on site and gives you the price in writing before any work starts.