Huebsch Washer Error Code E Ld: Water Leak During Drain
E Ld on Huebsch Quantum toploads, QN washer-extractors and CHM495R washer-extractors is a water leak drain error. The control saw the water level drop more than it should while the tub was not draining. Look for water under the washer, stay clear of electrical parts, and turn off the supply if a puddle is forming.
High: a real leak can put water on the floor near powered equipment.
What does Huebsch error code E Ld mean?
While a cycle is running and the drain is supposed to be closed, the tub level should stay put. The control keeps comparing the level reading with what it expects, and if the level falls more than it should when the tub is not draining, or when the drain valve should be shut, it shows "E Ld", a water leak drain error. On the QN models it also appears for one minute after the door is opened at the end of a cycle. Customers may find water on the floor. Leaks can come from the drain valve that does not seal, hoses and clamps with a slow weep, tub seals and gaskets, and sometimes the level sensor if the leak is only apparent. Water under the machine needs attention quickly because it can reach wiring and spread into the floor.
Affected models and control systems
This page applies to Huebsch Quantum topload washers in the TLW13C family, QN washer-extractors with the CHM1792C control, and CHM495R-family washer-extractors. The QN behavior of showing it for one minute after the door opens is specific to those models.
Code numbers and their meaning can change between control generations. We match the full model and control before acting on a code.
What you may notice
- Water on the floor beneath the washer
- "E Ld" shown on the display
- Water level in the tub dropping while it should hold
- A damp hose connection or wet floor after a cycle
Possible causes
Listed in Huebsch's documentation
- Drain valve that does not seal
- Hose or clamp with a slow leak
- Tub seal or gasket leaking
- Level sensor reading a leak that is not real
Other likely causes — what usually sits behind error code E Ld on this control. A technician confirms which one it is before any part is replaced.
- A clamp that has loosened from machine vibration at a drain hose connection
- A drain valve seat roughened by lint so it weeps when it should be closed
Safe checks before calling for service
- Look for water on the floor beneath the washer, staying clear of electrical parts.
- Press any key to clear the message on the QN models.
- Turn off the water supply if you see a puddle forming.
- Contact us to schedule service for the leak and note where the water appears.
How a technician diagnoses error code E Ld
- Read the code and watch the level during a drain-closed step.
- Inspect hoses, clamps and the drain valve for wetness.
- Check the tub seal and gaskets for leakage.
- Test the level sensor against the actual water level.
- Replace the leaking part only after finding the source.
- Leaking water near a powered machine is a shock risk if it reaches the wiring.
- Finding a tub seal leak means removing panels and working around live parts.
- A drain valve that fails to seal needs disassembly after the machine is isolated.
How error code E Ld differs from similar codes
E Ld is a leak found while draining or when the drain should be closed. E LF is the matching message for water rising during fill.
Technical reference
- Document
- Commercial Troubleshooting Topload Washers TLW13C, Part No. 203502R4, March 2024, Error Code Listing (pp. 30-32)
- Edition
- Part No. 203502R4, March 2024
- Models / control
- Quantum topload (TLW13C family) electronic control; CHM1792C family washer-extractor (QN models, 20-100 lb) front-end control; CHM495R family washer-extractor front-end control (20-100 lb)
- Section
- Section 3 General Troubleshooting - 20. Error Code Listing, printed pp. 30-32 (PDF pp. 32-34)
- Checked
- October 2026
We use the maker's document to read the code and do not reproduce it. Always confirm the complete model and control before applying these steps.
Related Huebsch washer error codes
Is it safe to keep using the washer?
Not while water is on the floor. Shut off the supply and have the leak found.
Why did it show after I opened the door?
On QN models the message can display for one minute after the door opens at the end of a cycle.
Could the sensor be wrong?
Yes, the manual lists the level sensor, but check for a real leak first.
Need help with Huebsch error code E Ld?
A technician confirms the cause on site and gives you the price in writing before any work starts.