Huebsch EDC Topload Washer Error Code E:0F: Infrared Programmed Off
E:0F means the infrared communicator on a Huebsch EDC control has been programmed off, so the control is deliberately ignoring the Micro-wand. The manual's step is to reprogram the infrared communicator on, using your setup sheet. The washer itself works normally.
Low: a setting blocks the programming link, but the washer keeps running.
What does Huebsch error code E:0F mean?
Every other Micro-wand code on the EDC describes a link that failed. E:0F describes a link that was switched off on purpose. The control has an option that turns the infrared communicator on or off, and with it off, the control does not listen for the Micro-wand at all, so the tool gets no response. Owners meet it when the wand shows no connection whatsoever, or when someone turned infrared off earlier, either for security or by mistake. The washer works normally, because only the programming side is closed. The cure is a setting, not a repair: the manual says to reprogram the infrared communicator on. The catch is that turning the setting back on usually has to be done from the control's own programming, since the wand cannot talk to a control that is not listening. The manual's causes are whether infrared was switched off in the control's options, who changed the setting last, the Micro-wand and its aim, and the communicator itself. The last two matter only if the setting turns out to be on already.
Affected models and control systems
E:0F is listed for Huebsch timer-type toploads with the EDC electronic control and the Micro-wand IIIe. Other controller generations handle infrared access differently.
Code numbers and their meaning can change between control generations. We match the full model and control before acting on a code.
What you may notice
- E:0F on the display when the wand is used
- The wand gets no connection at all
- The washer cycles normally
Possible causes
Listed in Huebsch's documentation
- Infrared switched off in the control's options
- Setting changed by someone earlier
- Micro-wand or its aim
- Communicator problem
Other likely causes — what usually sits behind error code E:0F on this control. A technician confirms which one it is before any part is replaced.
- Infrared turned off after a theft attempt or to stop staff reprogramming prices
- Options reset when a replacement control was installed
- Setting changed by accident while someone browsed the control's options
Safe checks before calling for service
- Reprogram the infrared communicator to on, using your setup sheet.
- Then re-aim the wand and try the exchange again.
- Keep the washer idle during the change.
- If you cannot turn it back on, phone us or send the online form, and tell us who last changed the options.
How a technician diagnoses error code E:0F
- Confirm the code appears whenever the wand is used, with a good aim.
- Review the control's option list and the setup sheet for the infrared setting.
- Switch the option on from the control's own programming and save it.
- Run a Micro-wand session to confirm it now connects.
- If the option reads on and the wand still fails, test the communicator and wiring.
- Changing control options without the setup sheet can alter pricing or cycle values that matter to the business.
- If the option is already on, the next test is wiring behind the cover, where mains voltage is present.
- Finding out who switched infrared off and why is part of a security review that belongs with the owner and a technician.
How error code E:0F differs from similar codes
E:0F is a deliberate setting, unlike E:01, E:09 and E:0A, which are aiming problems, and E:02, E:0B and E:0C, which are dropped links.
Technical reference
- Document
- Commercial Automatic Washer (Metered and Nonmetered) Troubleshooting H002C, Part No. 39201R9, Nov 2016 (EDC p.59, MDC p.72, NetMaster p.90)
- Edition
- Part No. 39201R9, November 2016
- Models / control
- Timer-type topload with EDC electronic control (Micro-wand IIIe)
- Section
- 32. EDC Error Code Listing, printed p. 59 (PDF p. 61); 41. MDC Error Code Listing, printed p. 72 (E:dr, E:FL, EC:19); 50. NetMaster Error Code Listing, printed pp. 90-93 (PDF pp. 92-95)
- Checked
- October 2026
We use the maker's document to read the code and do not reproduce it. Always confirm the complete model and control before applying these steps.
Related Huebsch washer error codes
Why would anyone turn infrared off?
The manual notes it may have been switched off for security, or by mistake.
Can the Micro-wand switch it back on?
Not if the control is not listening. The setting is changed from the control's own programming.
Is the washer safe to run?
Yes, it works normally. Only programming and data transfer are closed.
Need help with Huebsch error code E:0F?
A technician confirms the cause on site and gives you the price in writing before any work starts.