Huebsch EDC Topload Washer Error Code E:0C: Link Broken Mid-Session
E:0C is another infrared disconnection on the EDC control: the Micro-wand IIIe link was broken during the exchange, so the control stopped listening. Keep the infrared connection steady and run the exchange again. Nothing about the wash is wrong.
Low: the session fails, but the washer keeps running as before.
What does Huebsch error code E:0C mean?
E:0C belongs to the group of infrared disconnection codes, and the manual's owner step is to keep the infrared connection steady. What happened is that the link between the Micro-wand IIIe and the control was broken during the exchange, and the control stopped listening. The machine runs as before. What the code tells us is that the programming or data session did not complete, and it should be repeated. The causes listed are a Micro-wand moved before the exchange finished, a weak infrared emitter on the wand, a smudged communicator window breaking the beam, and a control receiver that loses the infrared signal. Compared with its neighbors, this listing puts more weight on the hardware side: the emitter on the tool and the receiver in the control, since a link that drops without anyone moving the wand is not a matter of aim. If the same tool works on another washer, the receiver is the suspect. If it fails there too, the emitter is. Cleaning the window and the wand's tip is the first inexpensive step.
Affected models and control systems
E:0C is listed for Huebsch timer-type toploads with the EDC electronic control and the Micro-wand IIIe. Other generations use different numbering for link problems.
Code numbers and their meaning can change between control generations. We match the full model and control before acting on a code.
What you may notice
- E:0C appears during a session
- The control stops responding to the wand
- Settings may be only partly sent
Possible causes
Listed in Huebsch's documentation
- Micro-wand moved before the exchange finished
- Weak infrared emitter on the wand
- Smudged communicator window breaking the beam
- Control receiver that loses the infrared signal
Other likely causes — what usually sits behind error code E:0C on this control. A technician confirms which one it is before any part is replaced.
- Wand tip coated with grime from a laundry-room pocket or bag
- Emitter weakened by a battery near the end of its life
- Ambient light from a nearby window flooding the receiver
Safe checks before calling for service
- Keep the infrared connection steady and run the exchange again.
- Clean the control window and the wand's tip.
- Stay still until the control confirms it finished.
- If E:0C persists, call us and we will test the link; tell us whether another wand behaves the same.
How a technician diagnoses error code E:0C
- Confirm E:0C appears mid-session and not at the start.
- Clean the wand tip and communicator window, and fit a fresh battery.
- Run the same session on another EDC washer.
- Try a second wand on this washer.
- Replace the wand, or test and replace the control's receiver, according to which pairing fails.
- Testing the receiver means opening the control area, where mains voltage is present.
- Telling an emitter problem from a receiver problem needs a second wand and a second washer.
- Any session that broke off may have left settings half written, which only a technician should verify and reload.
How error code E:0C differs from similar codes
E:0C is another infrared disconnection, like E:02 and E:0B, with more attention on the emitter and receiver hardware.
Technical reference
- Document
- Commercial Automatic Washer (Metered and Nonmetered) Troubleshooting H002C, Part No. 39201R9, Nov 2016 (EDC p.59, MDC p.72, NetMaster p.90)
- Edition
- Part No. 39201R9, November 2016
- Models / control
- Timer-type topload with EDC electronic control (Micro-wand IIIe)
- Section
- 32. EDC Error Code Listing, printed p. 59 (PDF p. 61); 41. MDC Error Code Listing, printed p. 72 (E:dr, E:FL, EC:19); 50. NetMaster Error Code Listing, printed pp. 90-93 (PDF pp. 92-95)
- Checked
- October 2026
We use the maker's document to read the code and do not reproduce it. Always confirm the complete model and control before applying these steps.
Related Huebsch washer error codes
Is E:0C the same as E:0B?
They are the same kind of event. The listing keeps them as separate numbers.
Why does it happen without moving the wand?
A weak emitter or a smudged window can break the beam.
Does the washer need to be taken out of service?
No. The machine runs as before.
Need help with Huebsch error code E:0C?
A technician confirms the cause on site and gives you the price in writing before any work starts.