Booking today · Miami, Los Angeles, Houston, New York and San Diego · three-hour arrival windows Independent commercial equipment repair · Every maker on this site Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(844) 393-0816 Schedule a Visit
Model series · Blendtec · Blenders

Blendtec Chef and EZ Series Kitchen Blenders

Current and older. 4 model numbers in this series.

Schedule a Visit(844) 393-0816
01Model numbers

Model numbers in this series

Find yours on the data plate. Letters after the base number usually mark the voltage, finish or door and do not change the repair.

  • Chef Blender
  • Chef 775
  • Chef 600
  • EZ 600

Repairs this series usually needs

  1. E-01 to E-06 messages on the Chef 775
  2. Overtemp Error
  3. Overload Error
  4. Touch Error on the Chef 775

The Blendtec Chef and EZ series are kitchen blenders: the Chef Blender, Chef 775, Chef 600 and EZ 600. The Chef 775 has an LED information center that shows E-01 to E-06. Some are current and others are older units still working in kitchens.

Overtemp Error means the motor is overheating, and Overload Error means it is overloaded. Touch Error appears on the Chef 775 when more than one sensor is touched. Power goes off at the outlet before anyone removes the jar. A jar that leaks may not be seated.

Chef and EZ blenders include current and older units, and we repair both. The price is in writing before we start, and a blender past saving gets a straight answer.

About this series

  • Kitchen blenders
  • Chef 775 has an LED information center
  • Current and older units
→Codes

Blendtec blenders codes

Error: Invalid blend cycleBlendtec Blender Error Message: Invalid Blend CycleError: Motor control error detectedBlendtec Blender Error Message: Motor Control Error DetectedError: Touch controller not detectedBlendtec Blender Error Message: Touch Controller Not DetectedError: Touch controller output is invalidBlendtec Blender Error Message: Touch Controller Output Is InvalidOverload ErrorBlendtec Blender Overload Error: Motor OverloadedOvertemp ErrorBlendtec Blender Overtemp Error: Motor OverheatingTouch ErrorBlendtec Blender Touch Error: Sensor TouchedE-01 to E-06Blendtec Chef 775 Blender Error Codes E-01 to E-06Error: Overload condition detectedBlendtec Commercial Blender Error Code Overload: Motor OverloadedError: Overtemp. Condition detectedBlendtec Commercial Blender Error Code Overtemp: Motor Too HotError: Read / Write error detectedBlendtec Commercial Blender Error Code Read / Write Error: Stored DataError: Reset error detectedBlendtec Commercial Blender Error Code Reset Error: Unexpected Reset
→Same maker

Other Blendtec blenders series

Blendtec Connoisseur Bar BlendersCurrent lineConnoisseur 825Connoisseur 825 SpacesaverBlendtec Stealth Series BlendersCurrent lineStealth 875Stealth 885Stealth 895 NBSStealth XStealth NitroStealth Nitro X
FAQBlendtec Chef and EZ Series Kitchen Blenders questions
What are E-01 to E-06?

They are error messages on the Chef 775 LED information center. The owner's manual does not explain each number, so we find the cause by testing.

What triggers Overload on a Chef?

The motor is overloaded. Press any button or cycle power, then unplug the blender and check for a blockage at the socket and blade. Keep fingers clear.

Which Chef models show E-01 to E-06?

The Chef 775 shows them on its LED information center. We read the number and test the control and sensors. You approve a written price ahead of any parts.

Book a visit

Book repair for your Blendtec Chef and EZ Series Kitchen Blenders

Tell us the maker, the model number from the data plate and what the unit is doing. We confirm a three-hour arrival window and give you a written price before any work starts.

(844) 393-0816
Open the booking form
☎ Call our office ▤ Schedule a Visit