Continental Girbau Inteli Washer Error Code 112: Value Out of Range
Code 112 means a value entered is out of range. Clear the starting time or wait and retry.
Low: an entry message that clears when a valid value is entered.
- Code
- 112
- Maker
- Continental Girbau
- Equipment
- Coin & card laundry
- Applies to
- E-Series washer-extractors with Inteli control (sheet names RMG055 and smaller, EH060 and larger)
What does Continental Girbau error code 112 mean?
When a delayed start time or another value is entered, the control checks it against what it accepts. If the value falls outside the allowed range, it displays 112 (Out of range) and ignores the entry. The manual's action is to clear the starting time or wait and retry. The sheet lists no individual causes, and it does not say which entries the code applies to, so we keep to the instruction given. The message appears while a person is programming or setting a start, so it is a response to the entry and not a failure of the machine. Entering the value again, within the range shown on the display, usually works. If the code appears again with an entry that looks reasonable, the clock or the stored setting may be the cause, and a technician can check the control. Pressing STOP returns the control to a ready state.
Affected models and control systems
Continental Girbau E-Series washer-extractors with Inteli control, sheet names RMG055 and smaller and EH060 and larger. Washers with Logi, LogiPro or Vended control use ALn alarms instead.
Code numbers and their meaning can change between control generations. We match the full model and control before acting on a code.
What you may notice
- Code 112 on the display
- Entry not accepted after a start time is set
- Control returns to the previous setting
Possible causes
Likely causes — what usually sits behind error code 112 on this control. A technician confirms which one it is before any part is replaced.
- Start time entered in the wrong format
- Clock on the control out of step with the time set
- Stored value left over from a past setting
Safe checks before calling for service
- Press STOP to clear the message.
- Clear the starting time.
- Wait a moment and enter the value again within the allowed range.
- If it returns for a normal value, note what you entered.
How a technician diagnoses error code 112
- Confirm what entry produced the code.
- Clear the starting time and retry.
- Check the control's clock and stored settings.
- Reset the setting to a known value.
- Replace the control board only if normal entries are refused.
- Control settings can affect how the washer starts.
- A persistent range error may point to the memory.
- Resetting stored values needs the maker's procedure.
How error code 112 differs from similar codes
Code 112 is an entry message. Codes 100 to 103 are program memory messages.
Technical reference
- Document
- Inteli Control Error Codes ST-102. R2 E-Series Inteli Control
- Maker documentation
- Continental Girbau owner support
- Edition
- 7/17/2023
- Models / control
- E-Series washer-extractors with Inteli control (sheet names RMG055 and smaller, EH060 and larger)
- Section
- Alarm table, p.1-5
- Checked
- October 2026
We use the maker's document to read the code and do not reproduce it. Always confirm the complete model and control before applying these steps.
Related Continental Girbau coin & card laundry error codes
Is code 112 an error in the washer?
No. The control is refusing an entry it cannot accept, and the washer is otherwise working. Try the entry again after clearing the starting time.
What do I do first?
Clear the starting time or wait and retry.
Will it keep happening?
Only if the same out-of-range value is entered. If a normal value is refused every time, note exactly what you entered and tell a technician, because a stored setting may be wrong.
Need help with Continental Girbau error code 112?
A technician confirms the cause on site and gives you the price in writing before any work starts.