MEIKO Commercial Dishwasher Error Code 17: Close Door While Emptying
Code 17 on the M-iClean U display reads Emptying / closing the door. The machine asks that the door be closed while it empties, and the manual's action is simply to close the door.
Low: an operator prompt to close the door; no part has failed.
- Code
- 17
- Maker
- MEIKO
- Equipment
- Dish machines
- Applies to
- Meiko M-iClean U glass, utensil and dishwashers, series M007DWUC10M*
What does MEIKO error code 17 mean?
When the M-iClean U empties its tank, it needs the door shut. If the door is open during that step, the control pauses and shows message 17, Emptying / closing the door. This is a prompt for the operator and is not a malfunction. The control reads the door signal during emptying and waits until it shows closed. The manual's action is two words: close door. No causes are listed, because the only trigger is the door state at that moment. The display reads Emptying / closing the door beside the number 17. A door that will not register as closed even when it looks shut is a different problem, and the manual does not discuss it for this entry, so mention it to a technician if it happens.
Affected models and control systems
This message is listed for the Meiko M-iClean U glass, utensil and dishwashers, series M007DWUC10M*, in section 9.4.1 Messages.
Code numbers and their meaning can change between control generations. We match the full model and control before acting on a code.
What you may notice
- Message 17 with the text Emptying / closing the door
- Emptying paused until the door is shut
- Water not draining while the door stays open
Possible causes
Likely causes — what usually sits behind error code 17 on this control. A technician confirms which one it is before any part is replaced.
- The machine is emptying its tank and the door is open
- Door closed but not latched all the way, so the switch does not register
- A rack or glassware caught at the door edge
- Door switch misaligned or worn so it reads open
Safe checks before calling for service
- Read the message and confirm it is 17.
- Close the door fully, checking that nothing sits in the door opening.
- Wait for emptying to continue and finish.
- If the message stays with the door shut, open and close it once more, firmly, and note whether the door latches normally.
How a technician diagnoses error code 17
- Confirm the door position signal changes when the door opens and closes.
- Check the door switch and its actuator alignment.
- Inspect door hinges, seals and the latch for wear or sag.
- Replace or realign the switch only after it fails the test.
- Door switch tests mean working at wiring in a machine that has live voltage and wet surfaces.
- Alignment of the door mechanism can affect the safety function of the machine.
- Water released during emptying is hot, so the machine has to be handled with care.
Technical reference
- Document
- M-iClean U Glass, utensil and dishwasher - Original operating instructions (types M007DWUC10M*-****)
- Edition
- 9763258 / Valid from: 2018-09 / Update: 2026-06
- Models / control
- Meiko M-iClean U glass, utensil and dishwashers, series M007DWUC10M*
- Section
- 9.4.1 Messages, printed pp. 43-45 of 70 (PDF pp. 43-45)
- Checked
- October 2026
We use the maker's document to read the code and do not reproduce it. Always confirm the complete model and control before applying these steps.
Related MEIKO dish machine error codes
Is code 17 an error?
No. The manual lists it as the machine asking for the door to be closed during emptying.
Why does it show even though the door is shut?
The door signal may not be registering. If a firm close does not clear it, a technician should check the switch.
How is 17 different from 18?
Both ask for the door to be closed. 17 appears during emptying, while 18 appears for a water change.
Need help with MEIKO error code 17?
A technician confirms the cause on site and gives you the price in writing before any work starts.