Booking today · Miami, Los Angeles, Houston, New York and San Diego · three-hour arrival windows Independent commercial equipment repair · Every maker on this site Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(844) 393-0816 Schedule a Visit
Error code · Henny Penny · Fryers

Henny Penny Pressure Fryer Error Code E-6A: Oil Temperature Probe

E-6A on a Henny Penny Velocity pressure fryer points to the oil temperature probe, which the control cannot trust, so cooking pauses. Turn the fryer off, pause briefly, and turn it on again, and let the oil cool before anyone looks at the probe area. If E-6A stays, stop cooking, do not pull on probe wires, and call us.

Medium · inspection needed

Medium: cooking pauses until the temperature reading is sound, and the fryer's separate high limit remains in place.

Schedule a Visit(844) 393-0816
Code
E-6A
Maker
Henny Penny
Equipment
Fryers
Applies to
Pressure fryers 500/600/561 (iControl-era online help)

What does Henny Penny error code E-6A mean?

The oil temperature probe is the control's only way to know how hot the oil is. If the probe circuit is open or shorted, the signal falls outside the range a working probe can produce, and the control shows E-6A. It then stops regulating the heat the usual way, because it is no longer sure where the temperature is. The maker's help page words the open versus shorted detail inconsistently, so we treat it as a probe circuit problem and test it rather than rely on the wording. The probe itself may have failed, a connector may be loose, the lead may be damaged by heat or oil, or the probe input on the board may be dead. From the display, wiring trouble and a board input problem look identical. A probe that tests well cold can still misbehave at frying temperature. The display holds the code, and cooking pauses until the reading is sound. The text is E-6A, and it applies to models such as the PFE 500 and PFE 561.

Affected models and control systems

Henny Penny Velocity pressure fryers such as the PFE 500 and PFE 561, as described in the iControl-era online help.

Code numbers and their meaning can change between control generations. We match the full model and control before acting on a code.

What you may notice

  • E-6A on the display
  • Cooking paused
  • Temperature display blank, stuck or jumping

Possible causes

Listed in Henny Penny's documentation

  • Oil temperature probe that has failed
  • Loose probe connector or damaged wire to the control
  • Heat or oil damage to the probe lead
  • Dead probe input on the control board

Other likely causes — what usually sits behind error code E-6A on this control. A technician confirms which one it is before any part is replaced.

  • A probe lead that insulates well cold but opens when the cabinet gets hot
  • Oil that wicked up the lead into the connector and corroded the pins

Safe checks before calling for service

✓ What an operator can do
  1. Turn the fryer off, pause briefly, and turn it on again, as the owner's manual lists.
  2. Let the oil cool before anyone looks closely at the probe area.
  3. If E-6A stays, stop cooking.
  4. Do not pull on probe wires.
  5. Then call us to have the probe tested, and tell us whether the display ever showed a temperature before the code.

How a technician diagnoses error code E-6A

  1. Confirm E-6A and let the oil cool.
  2. Disconnect the probe and measure its resistance at room temperature.
  3. Compare the reading with the expected value for the probe.
  4. Check the lead and connector for heat damage, breaks and oil intrusion.
  5. Test the probe input at the control with a known resistor or reference probe.
  6. Replace the probe, lead or board only after the matching test fails.
! Leave this to a technician
  • The probe sits in hot oil, and its lead runs through a cabinet with line-voltage parts.
  • We read the probe against a known value and test the wiring before ordering a part.
  • A probe that tests well cold can misbehave at frying temperature, which needs equipment to confirm.

Technical reference

Document
Henny Penny 4 Head Pressure Fryer online help, Error Codes
Maker documentation
Henny Penny owner support
Models / control
Pressure fryers 500/600/561 (iControl-era online help)
Section
Online help page 'Error Codes' - one Display / Cause / Solution table (HTML page, no page numbers); footer 2026 Henny Penny Corporation
Checked
October 2026

We use the maker's document to read the code and do not reproduce it. Always confirm the complete model and control before applying these steps.

→Same maker

Related Henny Penny fryer error codes

E-10 HIGH LIMIT TRIPPEDHenny Penny Electric Fryer Error Code E-10: High Limit TrippedE-15 DRAIN IS OPENHenny Penny Electric Fryer Error Code E-15: Drain Is OpenE-25 HEAT AMPS WERE TOO HIGHHenny Penny Electric Fryer Error Code E-25: Heat Amps Too HighE-25Henny Penny Electric Fryer Error Code E-25: High Heating CurrentE-26 HEAT AMPS ARE LOCKED ONHenny Penny Electric Fryer Error Code E-26: Heat Amps Locked OnE-26Henny Penny Electric Fryer Error Code E-26: Heating Current When OffE-27Henny Penny Electric Fryer Error Code E-27: Low Heating CurrentE-4 CPU TOO HOTHenny Penny Electric Fryer Error Code E-4: CPU Too HotE-5 FRYER TOO HOTHenny Penny Electric Fryer Error Code E-5: Fryer Too HotE-6 FRYER TEMP SENSOR FAILEDHenny Penny Electric Fryer Error Code E-6: Temp Sensor FailedE-70Henny Penny Electric Fryer Error Code E-70: Power Switch or I/O BoardControl error code E-10Henny Penny Evolution Elite Fryer Error Code E-10
E-6AQuestions about Henny Penny error code E-6A
Is E-6A open or shorted?

The maker's page is inconsistent on that detail, so we test the circuit instead of guessing.

Will a restart fix it?

It may clear once. A repeat means the probe circuit needs a test.

Can I fry without the probe?

No. The control needs it to regulate temperature safely.

Book a visit

Need help with Henny Penny error code E-6A?

A technician confirms the cause on site and gives you the price in writing before any work starts.

(844) 393-0816
Open the booking form
☎ Call our office ▤ Schedule a Visit