Electrolux Washer-Dryer Error Code 80: Incorrect Programming
Error code 80 means the dryer program unit found a programming error, or an incorrect or missing parameter. The manual equates it to E 10 in Selecta II. A technician should follow the Selecta II manual to correct the settings.
Low: a settings issue on the dryer side; no hardware has failed and the washing side is unaffected.
- Code
- Error code 80, INCORRECT PROGRAMMING
- Equipment
- Industrial laundry
- Applies to
- Compass Control dryer program unit
What does Electrolux Professional error code 80 mean?
A dryer program unit relies on stored programs and parameters to know how to heat, tumble and finish a cycle. If a program is not valid, or a parameter has a wrong value or is missing, the unit cannot carry out the cycle safely and shows ERROR 080 / INCORRECT PROGRAMMING. The manual gives the cause as a programming error, or an incorrect or missing parameter, and refers to E 10 in the Selecta II manual for the details. This is a settings matter, not a failed part. A newly installed board, a software update or a changed program can leave a parameter out of range. It is different from the washing side code 42, where the motor control holds no parameter set at all. Operators find that one program or all drying programs will not start, though the machine looks normal.
Affected models and control systems
This applies to the Compass Control washer-dryers WD4130 and WD4240, and the manual says the dryer codes apply only to these two. The code comes from the dryer program unit and corresponds to E 10 in the Selecta II manual.
Code numbers and their meaning can change between control generations. We match the full model and control before acting on a code.
What you may notice
- Display shows ERROR 080 / INCORRECT PROGRAMMING
- Drying program will not start
- Other programs may be accepted
- Message appears after a program or settings change
Possible causes
Likely causes — what usually sits behind error code 80 on this control. A technician confirms which one it is before any part is replaced.
- Parameter changed or lost during a software update or board replacement
- Program edited with a value outside the allowed range
- Settings reset to the wrong values after a power interruption
Safe checks before calling for service
- Think back to whether any program was edited or the board was changed recently.
- Switch the machine off and on once.
- Try a different drying program to see if only one is affected.
- Note which programs fail and what changed beforehand, then call us.
How a technician diagnoses error code 80
- Read the code and confirm it matches E 10 in the Selecta II manual.
- Follow the Service Manual for Selecta II for E 10.
- Review the dryer program and its parameters against the machine's settings.
- Correct or reload the missing or incorrect parameter.
- Test a full drying cycle.
- Programs and parameters are changed in the service menu and need the machine's own data.
- Wrong values can drive the heating or timing incorrectly.
- The correct values come from the Selecta II manual and the machine's setup.
How error code 80 differs from similar codes
Code 80 is a settings problem in the dryer unit; code 42 is a missing parameter set in the washer's motor control.
Technical reference
- Maker documentation
- Electrolux Professional owner support
- Edition
- 438 9228-61/EN, 2011.08.25
- Models / control
- Compass Control dryer program unit
- Section
- Troubleshooting, printed p.139 (Error codes)
- Checked
- October 2026
We use the maker's document to read the code and do not reproduce it. Always confirm the complete model and control before applying these steps.
Related Electrolux Professional industrial laundry error codes
Is a part broken?
Probably not. The manual describes a programming error or an incorrect or missing parameter.
Can I fix it by editing the program?
Leave that to a technician. The wrong value can affect heating.
Will it return?
It can if the underlying setting is not corrected.
Need help with Electrolux Professional error code 80?
A technician confirms the cause on site and gives you the price in writing before any work starts.