IPSO Washer-Extractor Error Code E Ld: Leak Detected on Drain
E Ld on an IPSO CHM495R washer-extractor is a water leak detection error tied to the drain valve: the level dropped when it should not have. Look for water under the machine, close the supply valves if a puddle spreads, and take the washer out of service.
High: water may be leaking from the machine, and the washer should not run until it is checked.
What does IPSO error code E Ld mean?
When the drain valve is meant to be closed, the water level in the drum should hold steady. The control keeps watching the level, and a fall with no drain commanded suggests water escaping while the machine thinks it is holding it. The control then raises E Ld. Staff may find water on the floor under the machine. A drain valve that does not seal is the first possibility. A leaking hose or clamp, a tub seal or gasket, and a level sensor that misreads, so the leak is only apparent, are the others. This page concerns the drain side. The matching alarm for water rising with no fill command is E LF. Because real water may be leaving the machine, the floor and the electrical parts around it are the first concern, and the machine should not keep running until it has been checked. In a busy laundry a small slow leak can go unnoticed for days.
Affected models and control systems
This applies to IPSO washer-extractors in the CHM495R family, 20 to 100 lb, with the front-end control in that programming manual.
Code numbers and their meaning can change between control generations. We match the full model and control before acting on a code.
What you may notice
- Water appears on the floor under the machine
- The drum level slowly falls while the drain is closed
- E Ld shows during a fill or wash step
Possible causes
Listed in IPSO's documentation
- Drain valve not sealing
- Hose or clamp leaking slowly
- Tub seal or gasket leaking
- Level sensing misreading, so the leak is only apparent
Other likely causes — what usually sits behind error code E Ld on this control. A technician confirms which one it is before any part is replaced.
- A drain valve seat roughened by lint and coins pulled in with the load
- A hose clamp loosened by machine vibration over months
Safe checks before calling for service
- Look for water on the floor under the machine, staying clear of electrical parts.
- Close the supply valves if a puddle is spreading.
- Put the machine out of service until it is checked.
- Contact us to schedule service, and tell us where the water appeared.
How a technician diagnoses error code E Ld
- Read the code and inspect the floor and the base of the machine for water.
- With the water drained and power locked off, inspect the drain valve, hoses and clamps.
- Check the tub seal and gaskets for seepage.
- Test the drain valve seal by holding water in the drum and watching the level.
- Compare the level sensor reading with the real level before replacing the valve or the sensor.
- Water near the machine's wiring is a shock hazard, so the area must be made safe before work begins.
- Testing the valve seal means holding water in the drum, which needs a controlled test and cleanup.
- A level sensor that misreads looks exactly like a real leak until the level is checked by hand.
How error code E Ld differs from similar codes
E Ld is level falling at the drain valve. E LF is level rising from a fill valve passing water.
Technical reference
- Document
- Washer-Extractor Programming CHM495R_SVG, Part No. F8208501ENR10, March 2017, Error Codes (pp. 36-37)
- Edition
- Part No. F8208501ENR10, March 2017
- Models / control
- CHM495R family washer-extractor front-end control (20-100 lb)
- Section
- Error Codes table, pp. 36-37 (E Pr only on Design 1 models; Ed01-Ed11 on Design 2 and 3 models)
- Checked
- October 2026
We use the maker's document to read the code and do not reproduce it. Always confirm the complete model and control before applying these steps.
Related IPSO washer error codes
Is a small puddle a reason to stop?
Yes. Water near electrical parts is a hazard, and a leak will grow.
Will it clear after a restart?
The message may, but a real leak remains.
Could the sensor be wrong?
Yes. If there is no water on the floor, a misreading level sensor is possible.
Need help with IPSO error code E Ld?
A technician confirms the cause on site and gives you the price in writing before any work starts.