Booking today · Miami, Los Angeles, Houston, New York and San Diego · three-hour arrival windows Independent commercial equipment repair · Every maker on this site Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(844) 393-0816 Schedule a Visit
Model series · TurboChef · High-speed ovens

TurboChef Bullet Rapid Cook Ovens

Current line. 1 model number in this series.

Schedule a Visit(844) 393-0816
01Model numbers

Model numbers in this series

Find yours on the data plate. Letters after the base number usually mark the voltage, finish or door and do not change the repair.

  • ENC-9600-801

Repairs this series usually needs

  1. F1 blower not running
  2. F2 cook temperature low
  3. F5 magnetron over temperature
  4. F10 communication between boards

The Bullet is a current TurboChef rapid cook oven, model ENC-9600-801. It was sold earlier as the Encore, and its prefix ENC comes from that name. It runs on 208/240V single-phase power with a NEMA 6-30 plug and uses a touch interface with an I/O board behind it.

The manual asks for 2 in clearance on all sides and 5 in above the oven. We see F1 for the blower and F2 for low cook temperature most often, with F5 and F6 when the rear fan guards clog or something blocks the side air. The owner clears the nozzles and the guards, and we test the heater, the blower and the boards.

We repair the Bullet at your location and give the price in writing first.

About this series

  • Rapid cook oven on 208/240V single-phase, NEMA 6-30
  • Touch user interface with an I/O board
  • Clearance of 2 in on all sides and 5 in above
  • Sold earlier as the Encore
→Codes

TurboChef high-speed ovens codes

F5TurboChef HhC Oven Error Code F5: Cook Cavity Too HotF7TurboChef HhC Oven Error Code F7: RTD FailureF8TurboChef HhC Oven Error Code F8: High Limit TrippedF9TurboChef HhC Oven Error Code F9: Belt Run FailureF1: Blower Running Status BadTurboChef High-Speed Oven Error Code F1: Blower Running Status BadF2: Cook Temperature Low (HhC: F2: Low Temp During Cook; C3: LOW COOK TEMP / F2 LOW TEMP)TurboChef High-Speed Oven Error Code F2: Cook Temperature LowF3: Magnetron Current Low (C3: LOW MAG CURR / F3 MAG CURR)TurboChef High-Speed Oven Error Code F3: Magnetron Current LowF4: Door Monitor Defective (C3: DOOR MONITOR / F4 MONITOR)TurboChef High-Speed Oven Error Code F4: Door Monitor DefectiveF5: Magnetron Over Temperature (C3: MAG OVER TMP / F5 MAG TEMP)TurboChef High-Speed Oven Error Code F5: Magnetron Over TemperatureF6: EC Temp (HhC: EC Over Temp; C3: ELEC OVR TMP / EC TEMP HIGH / F6 EC TEMP)TurboChef High-Speed Oven Error Code F6: Electrical Compartment HotFault Code: F8 Fault (listed with 'oven is not warming up properly')TurboChef High-Speed Oven Error Code F8: Oven Not Warming Up ProperlyHX RISE LOWTurboChef High-Speed Oven Message HX RISE LOW: Heater Not Rising
→Same maker

Other TurboChef high-speed ovens series

TurboChef C3 Convection Microwave OvensOlder lineC3/ABC3/CC3 MultiC3/C MultiTurboChef CIBO+ Rapid Cook OvensCurrent lineCBO-9500-1TurboChef ECO and ECO ST Rapid Cook OvensCurrent lineECO-9500-801ECO-9500-805ECS-9500-801ECS-9500-805ECO El BandidoECO ST El BandidoTurboChef Fire Artisan Pizza OvensCurrent lineFRE-9600-1FRE-9600-5FRE-9600-31TurboChef HhC 1618, 2020 and 2620 Conveyor OvensCurrent and olderHCS-9500-2CHCS-9500-2C-VHCS-9500-7CHCS-9500-7C-VHCT-9500-510-CHCT-9500-510-C-VHCT-9500-511-CHCT-9500-511-C-V+8 moreTurboChef High h Batch OvensCurrent and olderHHB-8601-1HHB-8601-1CHHB-8601-1DHHB-8601-1KHHD-9500-801HHD-9500-814-DLHHD-9500-877HHD-9500-878-DL+1 moreTurboChef i3 and i5 Rapid Cook OvensCurrent and olderI3-9500-801I3-9500-814-DLI5-9500-801-USI5-9500-814-DLI5-9500-1I5-9500-14-DLTurboChef PLEXOR M2 Multicook OvensCurrent linePLEXOR M2TurboChef Sota i1 Rapid Cook OvensCurrent and olderI1-9500-801I1-9500-836I1-9500-889I1-9500-905I1-9500-921I1-9500-938I1-9500-973
FAQTurboChef Bullet Rapid Cook Ovens questions
Is a Bullet the same as an Encore?

The Bullet is the current name, and the Encore is the earlier name that gave the ENC prefix. The service checks are similar, and we confirm the version on the oven.

Why does the Bullet need 5 in above?

The oven vents warm air upward and pulls cool air in from the sides. Blocking either one brings overheating messages, so keep shelves and boxes off the top and away from the sides.

What if the screen is blank?

Check the breaker and the plug first. If power reaches the oven and the screen stays dark, a board needs testing, and we do that on site.

Book a visit

Book repair for your TurboChef Bullet Rapid Cook Ovens

Tell us the maker, the model number from the data plate and what the unit is doing. We confirm a three-hour arrival window and give you a written price before any work starts.

(844) 393-0816
Open the booking form
☎ Call our office ▤ Schedule a Visit