Booking today · Miami, Los Angeles, Houston, New York and San Diego · three-hour arrival windows Independent commercial equipment repair · Every maker on this site Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(844) 393-0816 Schedule a Visit
Model series · TurboChef · High-speed ovens

TurboChef HhC 1618, 2020 and 2620 Conveyor Ovens

Current and older. 16 model numbers in this series.

Schedule a Visit(844) 393-0816
01Model numbers

Model numbers in this series

Find yours on the data plate. Letters after the base number usually mark the voltage, finish or door and do not change the repair.

  • HCS-9500-2C
  • HCS-9500-2C-V
  • HCS-9500-7C
  • HCS-9500-7C-V
  • HCT-9500-510-C
  • HCT-9500-510-C-V
  • HCT-9500-511-C
  • HCT-9500-511-C-V
  • HCT-9500-512-C
  • HCT-9500-512-C-V
  • HCW-9500-502C
  • HCW-9500-502C-V
  • HCW-9500-507C
  • HCW-9500-507C-V
  • HCW-9500-512C
  • HCW-9500-512C-V

Repairs this series usually needs

  1. F1 blower failure
  2. F5 cook cavity over temperature
  3. F8 high limit tripped
  4. F9 belt run failure
  5. F7 RTD failure

The HhC conveyors are TurboChef high-speed ovens that carry food through on a belt. The model prefix gives the size: HCS is the 1618, HCT is the 2020 and HCW is the 2620. A V at the end of the model means the ventless version. The manual asks owners to keep the room under 100 F and the filters clean.

The conveyor messages are F1 for the blower, F2 for low cook temperature, F5 for cavity over temperature, F6 for the electrical compartment, F7 for the RTD, F8 for the high limit and F9 when the belt stops. A hot kitchen, clogged filters and food on the belt cause many of them. We test the drives, the heaters and the relays.

We repair HhC ovens at your location and quote in writing first.

About this series

  • Ventless high-speed conveyor oven
  • HCS is the 1618, HCT is the 2020 and HCW is the 2620
  • A V at the end of the model marks the ventless version
  • Keep the room under 100 F with clean filters and running fans
→Codes

TurboChef high-speed ovens codes

F5TurboChef HhC Oven Error Code F5: Cook Cavity Too HotF7TurboChef HhC Oven Error Code F7: RTD FailureF8TurboChef HhC Oven Error Code F8: High Limit TrippedF9TurboChef HhC Oven Error Code F9: Belt Run FailureF1: Blower Running Status BadTurboChef High-Speed Oven Error Code F1: Blower Running Status BadF2: Cook Temperature Low (HhC: F2: Low Temp During Cook; C3: LOW COOK TEMP / F2 LOW TEMP)TurboChef High-Speed Oven Error Code F2: Cook Temperature LowF3: Magnetron Current Low (C3: LOW MAG CURR / F3 MAG CURR)TurboChef High-Speed Oven Error Code F3: Magnetron Current LowF4: Door Monitor Defective (C3: DOOR MONITOR / F4 MONITOR)TurboChef High-Speed Oven Error Code F4: Door Monitor DefectiveF5: Magnetron Over Temperature (C3: MAG OVER TMP / F5 MAG TEMP)TurboChef High-Speed Oven Error Code F5: Magnetron Over TemperatureF6: EC Temp (HhC: EC Over Temp; C3: ELEC OVR TMP / EC TEMP HIGH / F6 EC TEMP)TurboChef High-Speed Oven Error Code F6: Electrical Compartment HotFault Code: F8 Fault (listed with 'oven is not warming up properly')TurboChef High-Speed Oven Error Code F8: Oven Not Warming Up ProperlyHX RISE LOWTurboChef High-Speed Oven Message HX RISE LOW: Heater Not Rising
→Same maker

Other TurboChef high-speed ovens series

TurboChef Bullet Rapid Cook OvensCurrent lineENC-9600-801TurboChef C3 Convection Microwave OvensOlder lineC3/ABC3/CC3 MultiC3/C MultiTurboChef CIBO+ Rapid Cook OvensCurrent lineCBO-9500-1TurboChef ECO and ECO ST Rapid Cook OvensCurrent lineECO-9500-801ECO-9500-805ECS-9500-801ECS-9500-805ECO El BandidoECO ST El BandidoTurboChef Fire Artisan Pizza OvensCurrent lineFRE-9600-1FRE-9600-5FRE-9600-31TurboChef High h Batch OvensCurrent and olderHHB-8601-1HHB-8601-1CHHB-8601-1DHHB-8601-1KHHD-9500-801HHD-9500-814-DLHHD-9500-877HHD-9500-878-DL+1 moreTurboChef i3 and i5 Rapid Cook OvensCurrent and olderI3-9500-801I3-9500-814-DLI5-9500-801-USI5-9500-814-DLI5-9500-1I5-9500-14-DLTurboChef PLEXOR M2 Multicook OvensCurrent linePLEXOR M2TurboChef Sota i1 Rapid Cook OvensCurrent and olderI1-9500-801I1-9500-836I1-9500-889I1-9500-905I1-9500-921I1-9500-938I1-9500-973
FAQTurboChef HhC 1618, 2020 and 2620 Conveyor Ovens questions
How do I know which HhC I have?

The model prefix tells you: HCS is the 1618, HCT is the 2020 and HCW is the 2620. The number after it gives the version.

Why does the belt stop with F9?

Overload, an obstruction, a dirty oven or overheated conveyor drives can stop it. With the oven off and cool, clear the belt and check the filters and fans.

Does the oven need a hood?

The ventless versions, marked with a V, do not need one. They still need clean filters, running fans and cool surroundings to run well, so the room matters even without a hood.

Book a visit

Book repair for your TurboChef HhC 1618, 2020 and 2620 Conveyor Ovens

Tell us the maker, the model number from the data plate and what the unit is doing. We confirm a three-hour arrival window and give you a written price before any work starts.

(844) 393-0816
Open the booking form
☎ Call our office ▤ Schedule a Visit