Booking today · Miami, Los Angeles, Houston, New York and San Diego · three-hour arrival windows Independent commercial equipment repair · Every maker on this site Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(844) 393-0816 Schedule a Visit
Brand · Fryers

Henny Penny Fryer Repair

We repair Henny Penny pressure fryers and open fryers, from current Velocity and Evolution Elite models to older Computron machines, in Miami, Los Angeles, Houston, New York and San Diego. The price is in writing before work starts.

1kind of equipment
8model series listed
48error codes explained
30 daysworkmanship warranty
01What goes wrong

Common Henny Penny problems we fix

In plain words, the way kitchen and laundry staff describe them when they call.

01

Pressure fryer will not build pressure

02

E-10 high-limit message

03

E-15 drain open message

04

Gas fryer fails to ignite

05

Heating error on electric fryer

06

Probe error on the display

07

Filter pump trouble

Henny Penny Models We Handle

Henny Penny is best known for pressure fryers, and we service every generation. The current Velocity PFE 500, PFE 561 and PFG 600 four-head and six-head fryers sit alongside eight-head High Volume machines such as the PFE 591 and PFG 691. For open fryers we repair Evolution Elite EEE and EEG units, the 320 and 340 series OFE and OFG fryers, and older OG, OE and LVE open fryers. Legacy pressure fryers from the 561, 580, 590, 600 and 690 era are still out there too.

What the E-Codes Tell Us

These fryers report a lot through E-codes, so we start at the display. E-10 is a high-limit trip, often after overheating or after the drain was opened while the fryer was heating. E-15 points to the drain-open switch. The E-6 family means a probe problem. On electric models E-25, E-26 and E-27 are heat-amp errors, and on gas models with electronic ignition the E-20 family is an ignition failure. E-16 sends us to inlet gas pressure, which should be at least 7 inches of water column on natural gas and 11 on propane.

A pressure fryer that will not build pressure most often has a worn lid gasket, while filtration trouble comes from the pump and its parts. Grease buildup and humid air, especially near the coast in Miami and Houston, wear seals and connectors faster. Before the visit we confirm the model and control, such as Computron 8000 or iControl. If an old fryer is not worth the money we say so, and you get a written price first and a 30-day warranty on our work.

→Error codes

Henny Penny codes and alarms

What the display or the blinking light means, what is safe to check, and when to stop and call us.

E-10 HIGH LIMIT TRIPPEDHenny Penny Electric Fryer Error Code E-10: High Limit TrippedE-15 DRAIN IS OPENHenny Penny Electric Fryer Error Code E-15: Drain Is OpenE-25 HEAT AMPS WERE TOO HIGHHenny Penny Electric Fryer Error Code E-25: Heat Amps Too HighE-25Henny Penny Electric Fryer Error Code E-25: High Heating CurrentE-26 HEAT AMPS ARE LOCKED ONHenny Penny Electric Fryer Error Code E-26: Heat Amps Locked OnE-26Henny Penny Electric Fryer Error Code E-26: Heating Current When OffE-27Henny Penny Electric Fryer Error Code E-27: Low Heating CurrentE-4 CPU TOO HOTHenny Penny Electric Fryer Error Code E-4: CPU Too HotE-5 FRYER TOO HOTHenny Penny Electric Fryer Error Code E-5: Fryer Too HotE-6 FRYER TEMP SENSOR FAILEDHenny Penny Electric Fryer Error Code E-6: Temp Sensor FailedE-70Henny Penny Electric Fryer Error Code E-70: Power Switch or I/O BoardControl error code E-10Henny Penny Evolution Elite Fryer Error Code E-10E 5 / PROB / E 41Henny Penny Fryer Computer Codes E 5, PROB and E 41E-13A / E-13BHenny Penny Fryer Error Code E-13A / E-13B: Pressure Assist SensorE-15Henny Penny Fryer Error Code E-15: Drain Open or Switch ProblemE-47Henny Penny Fryer Error Code E-47: Analog Converter or 12 V SupplyE-5Henny Penny Fryer Error Code E-5: Oil Too Hot or Bad Probe ReadingE-70AHenny Penny Fryer Error Code E-70A: Wiring or I/O Board ProblemE-70DHenny Penny Fryer Error Code E-70D: Fryer Type Set WrongE-20CHenny Penny Gas Pressure Fryer Error Code E-20C: Ignition ModuleE-20DHenny Penny Gas Pressure Fryer Error Code E-20D: Burner Did Not LightE-10Henny Penny OFG-391 Fryer Error Code E-10: High Limit TrippedE-15Henny Penny OFG-391 Fryer Error Code E-15: Drain SwitchE-20AHenny Penny OFG-391 Fryer Error Code E-20A: Pressure Switch Stuck Closed

All 48 Henny Penny fryers codes

FAQHenny Penny questions
What does an E-10 mean on a Henny Penny fryer?

E-10 is a high-limit trip. It can follow overheating or a drain opened while the fryer was heating. Let the oil cool, then call us to test the limit, the probe and the heating circuit.

Can you repair older Henny Penny pressure fryers?

Yes. We work on older 561, 580, 590, 600 and 690 pressure fryers with Computron controls as well as current models. If an older fryer is not worth repairing, we tell you before you pay for parts.

My Henny Penny gas fryer will not ignite. What should I check?

If you smell gas, everyone leaves the kitchen and the gas utility gets the call from outside. With no odor, make sure the gas valve is open and the fryer is plugged in, then call us and we will test the ignition system and inlet gas pressure.

Book a visit

Book Henny Penny repair in Miami, Los Angeles, Houston, New York and San Diego

Tell us the maker, the model number from the data plate and what the unit is doing. We confirm a three-hour arrival window and give you a written price before any work starts.

☎ Call our office ▤ Schedule a Visit